Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Granada Hills Homeowners
Rain isn’t the only thing Granada Hills weather sends at your chimney. The Santa Ana winds that funnel through the north San Fernando Valley drive water sideways, straight into an open or cracked flue, and a cap that’s lost a bolt or a crown with a hairline crack lets that water soak the masonry all winter. That’s the number one cause of chimney water damage, and it’s exactly what a chimney cap and crown are supposed to stop before rot and rust set in.
Our technicians have up to 10 years of experience fitting caps and repairing crowns across the Valley, and we work with professional-grade product lines like Gelco and Copperfield caps and HeatShield crown resurfacing because we’ve seen how off-brand pieces hold up after a couple of windy seasons. We inspect before we recommend anything, and we can often get a repair booked in the same day. Call (855) 774-3956 to set up your free estimate.
What Our Chimney Cap & Crown Service Includes
Chimney caps and crowns are two different jobs on two different parts of the chimney, and we handle both from the top down. Here’s what each piece of the work involves.
Cap Installation
A chimney cap is the hooded, screened cover that sits on top of the flue and keeps rain, birds, squirrels and wind-blown debris out of the chimney. If your flue is open and you burn regularly, you want a cap installed before the rainy months arrive. We measure the flue, fit a Gelco or Copperfield cap that seals correctly, and anchor it so the Santa Ana gusts can’t shift it.

Cap Replacement
Caps rust out, lose screws, dent, or get knocked loose by wind and debris over time, and a cap that’s sitting crooked or missing its screen does more harm than good. When we inspect a worn cap, we show you the damage at the top and in the flue so you can decide whether it needs swapping. We remove the old unit and install a proper replacement that matches your flue dimensions.

Crown Repair
The crown is the sloped concrete or mortar cap at the very top of the masonry that sheds water away from the chimney body. Hairline cracks in the crown let water seep into the brickwork and freeze-and-thaw isn’t the concern here, but constant moisture soaking the mortar joints absolutely is. We patch and rebuild damaged crowns so the slope is restored and water runs off the way it was designed to.

Crown Coating
Crown coating is a protective sealant applied over a sound crown to close small cracks and add a flexible, water-resistant layer. It’s a smart option when the crown is basically intact but showing surface wear. We use HeatShield crown materials, so the finish bonds to the masonry and holds up through hot Valley summers and wet winters.
Multi-Flue Cap
If your chimney serves more than one flue, a single multi-flue cap covers them all under one housing. These are common on larger Granada Hills homes with a fireplace plus a furnace flue, and they need proper sizing so each flue still drafts cleanly. We build these to fit the whole stack, not as a one-size compromise.
Custom Cap
Some chimneys need a cap that isn’t standard stock, whether it’s an odd flue shape, an oversize crown, or a look the homeowner wants to match. We fabricate custom caps in durable metal to your chimney’s exact dimensions. You get a piece that fits the first time and stays put through a windy season.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with industry-trusted materials because the difference shows up years down the line. Gelco caps are a standard we install often, and we know exactly which seams and fasteners are the first to go on a worn Gelco unit, so we can tell you whether yours is serviceable or ready for replacement. Same with Copperfield specialty products, where the fit and finish matter as much as the material. When a crown needs resurfacing rather than a full rebuild, HeatShield is what we reach for, because it’s formulated to bond to masonry and hold.
The call on any of these parts is the same: we inspect before we recommend, so you’re not paying to replace something that has plenty of life left. Our technicians have up to 10 years of experience and have seen how each of these brands wears in real Valley conditions. Whether you have a Gelco cap, a Copperfield unit, or any other make, we can help.
Signs You Need Chimney Cap & Crown Right Now
- Water in the firebox or rust on the damper. If you’re seeing moisture or rust stains inside after a rain, the cap or crown isn’t shedding water properly. That water is also working into the masonry, so it’s worth a look before the next storm.
- A cracked or crumbled crown. Small cracks widen over seasons, and a crown that’s breaking apart lets water into the very top of the chimney. We can repair it before it turns into a bigger masonry job.
- A cap that’s loose, missing, or full of holes. A dented or rusted cap can let birds and debris in and stop blocking rain. A quick replacement restores the protection.
- Masonry stains or efflorescence on the outside. White staining or dark streaks on the chimney exterior often mean water is getting in up top. The crown and cap are the first places we check.
- Animal or debris problems. Nesting birds or squirrels in the flue usually point to a missing or damaged cap screen. A proper cap keeps them out so you’re not dealing with blockages or odors.
Our Chimney Cap & Crown Process – Step by Step
Every job follows the same order, because the inspection tells us what the estimate should be. Here’s how it goes.
- 1
Initial inspection. We start at the top and work down, checking the crown, the cap, the flue and the firebox. We use a camera in the flue when needed so we can see what the eye can’t, and we tell you what we find before recommending a single part.
- 2
Photo report and clear findings. You get a written summary with photos of the crown, cap and flue, so you can see the actual condition and not take our word for it. If something can safely wait, we’ll tell you that too.
- 3
Written flat-price estimate. We price the job by scope and put it in writing, so there’s no surprise when the work is done. You approve the estimate before we touch anything.
- 4
The repair or installation. We install the cap, patch or recoat the crown, or fabricate a custom piece as agreed, using Gelco, Copperfield, HeatShield or whichever professional-grade material fits the job.
- 5
Final check and walkthrough. We verify the cap is seated and secure and the crown sheds properly, then walk you through the finished work. You’ll know exactly what we did and why.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Granada Hills?
The honest answer is that it depends on how much of the crown is damaged and which cap fits your flue, but here are typical ranges for common jobs in Granada Hills. A standard cap installation usually runs $180 to $450 depending on flue size and cap style. Crown repair for small cracks falls around $300 to $700, while a full crown rebuild on a badly deteriorated top can run $750 to $1,500 or more depending on the chimney’s size and access. Crown coating on a sound crown is usually the lower end of that range. Custom caps and multi-flue caps sit higher because the fabrication is built for your exact stack.
What affects the price: the size and number of flues, whether the crown needs patching or rebuilding, roof pitch and access, and the material you choose. To avoid overpaying, get the inspection findings and a written estimate in hand before anything is ordered, and ask whether the work can safely wait. Our estimates are free, and the written estimate sets the final price. We don’t quote against parts we haven’t seen on your chimney, and we won’t push a crown rebuild when a repair will do.
Chimney Cap & Crown Near Granada Hills – Our Service Area
We serve Granada Hills and the surrounding north Valley and Santa Clarita communities, including Stevenson Ranch, Sunland, Santa Susana, Northridge, San Fernando, Sylmar, Panorama City, Porter Ranch, Lake Balboa, Chatsworth and Reseda. Our chimney cap & crown work is booked by area, and we dispatch Sunday through Friday, 7am to 7pm, with same-day when the schedule allows. For nearby neighborhoods, request your free estimate here, or read more about chimney sweep Granada Hills to see the rest of what we do.
Serving Granada Hills, CA – Our Local Coverage Area
We serve Granada Hills and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Granada Hills
A chimney cap is the screened, hooded cover on top of the flue, and the crown is the sloped concrete or mortar top of the masonry. The cap keeps rain, animals and debris out of the flue, while the crown sheds water away from the brickwork. Together they’re the chimney’s first line of defense against water damage.
Most cap installations take under two hours, and crown repairs usually run a few hours depending on the extent of the damage. A full crown rebuild or a custom-fabricated cap can take longer, and we’ll give you a realistic window with your written estimate. We don’t leave the work half-finished or hand it to another contractor.
Typical ranges are $180 to $450 for a standard cap installation and $300 to $1,500 for crown repair or rebuild depending on the damage. Custom and multi-flue caps run higher. An inspection is the only way to get a firm number, and our estimate is free. Call (855) 774-3956 for an exact quote.
Yes, we work with Gelco and Copperfield caps and HeatShield crown materials, and we can service most other makes as well. If your existing cap or crown is a brand we don’t stock, we’ll still inspect it and tell you the best path forward. Whether you have one of those brands or any other make, we can help.
Same-day appointments are often available when the schedule allows, and we dispatch Sunday through Friday, 7am to 7pm, so the phone line stays open when the work needs to get booked. We answer 24/7. A call outside dispatch hours is booked into the next opening. We’re closed Saturday.
We stand behind the installation and repair we perform and will make it right if something we installed isn’t doing its job. That’s part of why we use professional-grade products rather than off-brand pieces that fail early. Ask about our guarantee when you book your estimate.
Clear the fireplace area and the floor in front of the hearth so we have room to work, and make sure we can reach the roof or the chimney from the ground. Move any vehicles that might block access to the roof line. Beyond that, you don’t need to do anything; we bring the materials and handle the rest.
Schedule Your Chimney Cap & Crown Service in Granada Hills Today
One call covers it, from the firebox to the crown, with an inspection first and a written estimate before any work begins. We work with the brands professionals trust and we tell you when a repair can safely wait. Call (855) 774-3956 for your free, no-obligation estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Granada Hills.